- Combines isolating and venting in a single valve, eliminating the need for tubing and fittings
- Block valve isolates the downstream process fluids, and the bleed valve exhausts upstream fluids enabling instruments to be removed without disturbing the permanent piping installation on the bottom
- The 1/4" NPT vent plug is located 90° to the left and may be removed and replaced with exhaust piping to direct the fluids to a safe location
- 100% helium leak tested to 1 x 10-4 ml/s for guaranteed performance and reliability
- 10,000 psi hard seat pressure rating @ 200 °F
- Blow-out proof stem provides a secondary stem seal in the full open position
- FKM o-ring seal and PTFE back-up ring below the stem threads to protect from corrosion and galling; PTFE or Graphite packing optional
- All stems are 316 Stainless Steel
- All stem threads are rolled for strength and ease of operation
- One-piece bonnet with a metal-to-metal seal to the valve body below the bonnet threads
- Slotted spring pin to prevent accidental loosening
- Vinyl dust cap for bonnet and stem (non-packing)
If you are viewing on a smaller screen or with screen zoom, please use
the horizontal scroll bar at the bottom of this table to see all information.
ORDERING INFORMATION
| SERIES |
3 |
3-valve |
|
|
|
|
| SEAT |
0 |
Hard seat |
|
|
|
|
| PROCESS TYPE |
7 |
Block & bleed |
|
|
|
|
| CONNECTION SIZES |
0 |
1/2" NPT |
2 |
1/4" NPT |
|
|
| VALVE TYPES |
MFC |
Male-Female, Steel |
FMC |
Female-Male, Steel |
FFCR |
Female-Female, Steel, Right Vent |
| MFCR |
Male-Female, Steel, Right Vent |
EFMC |
Extended Female-Male, Steel |
EFFC |
Extended Female-Female, Steel |
| EMFC |
Extended Male-Female, Steel |
FMS |
Female-Male, Stainless Steel |
FFS |
Female-Female, Stainless Steel |
| MFS |
Male-Female, Stainless Steel |
EFMS |
Extended Female-Male, Stainless Steel |
FFSR |
Female-Female, Stainless Steel, Right Vent |
| MFSR |
Male-Female, Stainless Steel, Right Vent |
FFC |
Female-Female, Steel |
EFFS |
Extended Female-Female, Stainless Steel |
| EMFS |
Extended Male-Female, Stainless Steel |
|
|
|
|
To meet all of your specific application requirements, the following additional options are available for these needle valves. To order all or any of these
options, simply add them to the part number as shown in the diagram below.
NOTE 1: The example shown includes ALL possible additional options. Please include ONLY the options required for your application when building your part number. (EXAMPLE: 3070-FFC-HL5)
NOTE 2: When a packing option is selected, an o-ring option is NOT available.
ORDERING INFORMATION - Additional Options
| PACKINGS† |
P1 |
PTFE |
P2 |
Graphite |
|
|
| STEM TIPS |
T1 |
Non-rotating (316 stainless) |
T6 |
Ball (carbide) |
T8 |
Ball (Monel) |
| T5 |
Ball (440C stainless) |
T7 |
Ball (ceramic) |
T9 |
Non-rotating regulating (316 Stainless) |
| O-RINGS* |
EM1 |
EPDM |
KZ1 |
FFKM (Perfluoroelastomer) |
NB1 |
NBR |
| HANDLES |
HL1 |
1-13/16" Mini "T" |
HL3 |
1" Round knurled |
HL5 |
1-3/4" Phenolic |
| |
HL2 |
2-1/2" "T" |
HL4 |
1-3/8" Phenolic |
|
|
† If a packing option is chosen, maximum pressure rating is 6,000 psi. Refer to the "Pressure vs Temperature: Packing Style with Compatible Fluid" chart.
* Other o-ring materials available on request.
Please note that the standard o-ring in all the NOSHOK valves is FKM and the standard handles are block “T” handles (HL2) and bleed 1-3/8" mini “T” handle (HL7).
The handle material will always match the material of the valve, unless otherwise specified. For example, the "T" handle (HL2) on the 3070-FFC will be steel. When only the standard configuration is needed, no additional designations are necessary. Please consult the factory for special application requests.
To meet all of your specific application requirements, the following additional options are available for these needle valves. To order all or any of these options, simply add them to the part number as shown in the diagram below.
NOTE 1: The example shown includes ALL possible additional options. Please include ONLY the options required for your application when building your part number. (EXAMPLE: 3070-FFC-HL5)
NOTE 2: When a packing option is selected, an o-ring option is NOT available.
If you are viewing on a smaller screen or with screen zoom, please use
the horizontal scroll bar at the bottom of this table to see all information.
| SPECIFICATIONS |
| Materials |
Zinc-nickel plated steel, electropolished 316 Stainless Steel |
| Connections |
1/2" & 1/4" NPT Male-female & Female-female configurations available, right venting optional |
| Pressure ratings* |
10,000 psi @ 200 °F |
| Orifice size |
0.187" |
| Flow coefficient |
CV 0.44 |
| Steam seal & type |
All 316 Stainless Steel stems with FKM o-ring and PTFE back-up ring below the threads, PTFE or Graphite packing optional |
| Length |
4" standard and 5-3/8" extended length available |
| Options |
Panel mountings, o-ring materials, handles, packings, regulating stem and stem tips |
| Weight |
Approximately 3.2 lb. |
* If a packing option is chosen, maximum pressure rating is 6,000 psi. Refer to the "Pressure vs Temperature: Packing Style with Compatible Fluid" chart.
All NOSHOK valve products conform to the MSS SP-99 instrument valves standards, and valves supplied with packing also conform to MSS SP-132 compression packing systems for instrument valves standard.
Convert to PT Series
NEW
.jpg)
