5530 Series 5-Valve Natural Gas Manifold Valves, Soft Seat/Tip (0.375” Orifice)

• Packing
• PTFE Manifold Gasket Ring (RG1-TF1)
• Graphite Manifold Gasket (RG1-GF1) 
• Traditional to Coplanar Flange Adaptor (TCA-S)

• NOSHOK offers non-stabilized and stabilized Connectors, with or without an integral block valve
• These connectors are designed to reinforce the entire installation by shifting radial-stress load away from the NPT connections
• Mounted onto the orifice flange or the orifice fitting, connectors are sometimes referred to as a “Root Valve” or primary isolation valve

View NOSHOK Connectors

Dielectric Kits are designed to maintain the integrity and reliability of the pipeline and piping system through safety and corrosion protection. Dielectric Kits provide a non-conductive barrier between the process piping and the instrument and isolate components from the effects of electrical current. By eliminating metal-to-metal contact, current is halted to prevent corrosion and aid in the cathodic protection of the system.

• One Piece Dielectric Gasket, Pair, Steel, Acetal (DK1)
• One Piece Dielectric Gasket, Pair with Stainless Steel Bolts, Stainless Steel, Acetal (DK1-SS)
• PTFE Gasket with Dielectric Shim, Pair, Steel, PTFE, PVC (DK2)

DK1

• Single piece design combining a Acetal sealing gasket and Acetal dielectric shim
• Bolts, washers and dielectric bushings are included with the kits
• Cannot be used in conjunction with seal rings or o-rings
• Seal rings or o-rings not required

DK2

• Used as an alternative to a one-piece design when a separate sealing gasket or o-ring is required
• Two piece design consisting of a PTFE sealing gasket and PVC dielectric shim
• Bolts, washers and dielectric bushings are included with the kits

Specifications:

• Material: Acetal, PVC
• Max operating temp 150 °F
• Dielectric strength exceeds 1/32 air arc gap approximately 2,500 Vdc

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

NOSHOK Differential Pressure to Differential Pressure Adaptors allow two differential pressure transmitters to be mounted on a single set of orifice taps. This configuration is ideal for applications such as bi-directional flow, and custody transfer where only a single set of orifice taps is available. Multiple adaptors are available for various application configurations and space restrictions.

• ΔP to ΔP Adaptor - 3/8” Bore, 23” Length, Steel (DP1-DP1-CS)
• ΔP to ΔP Adaptor - 3/8” Bore, 23” Length, Stainless Steel (DP1-DP1-SS)
• ΔP to ΔP Adaptor - 3/8” Bore, 9” Length, Steel (DP2-DP2-CS)
• ΔP to ΔP Adaptor - 3/8” Bore, 9” Length, Stainless Steel (DP2-DP2-SS)

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

Used on gas pipelines, the Differential Pressure to Static Adaptor Plate is used to mount a differential pressure transmitter and a static pressure transmitter to a five valve flange-flange manifold. They are available in Zinc-Nickel plated Steel, electropolished Stainless Steel. An integral mini style bleed valve is incorporated in the plate and a 1/4" NPT vent plug is provided. The mini style bleed valve is equipped with a FKM o-ring and PTFE back-up ring below the stem threads to protect against corrosion and galling. Stem threads are rolled for greater strength and ease of operation and all NOSHOK valves are 100% helium leak tested for guaranteed reliability. Maximum pressure rating of 10,000 psi for Steel & Stainless Steel models.

• ΔP to Static Adaptor, Steel (DP1-SA1-CS)
• ΔP to Static Adaptor, Stainless Steel (DP1-SA1-SS)

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The NOSHOK Direct Connect Assembly provides an installation that keeps the meter close to the orifice taps for accurate flow measurements.

View the NOSHOK Direct Connect Assembly

The Flare Pattern™ valve configuration (FP) is an available option on NOSHOK 5030/5130 and 5530 Series 5-valve natural gas manifold valves. The equalization valves and vent valve on these manifolds are angled to provide maximum clearance for fingers during operation.

Futbols (flange adapters) bolt to the process side of a flange-flange manifold to allow connection of process flange taps or process root valves. Futbols also allow flanges to be connected to threaded process piping while maintaining the ease of removal or repair of the manifold if maintenance is required. The futbols provide a 1/16" offset connection from the bolt holes to give connection centers of 2", 2-1/8" or 2-1/4".

Specifications:

• Carbon Steel Futbol, Pair, Steel (50FA1-CS)
• Stainless Steel Futbol, Pair, Stainless Steel (50FA1-SS)
• Material: Zinc-Nickel plated Steel, 316 Stainless Steel
• Connections: 1/2" NPT
• Kit Includes: (2) Futbols, (4) hex bolts 7/16"-20, (2) PTFE face seals
• Weight approximately 2.1 lb.

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The manifold mounting kit is designed for direct or remote mounting to a two-inch pipe stand. This kit can be used with any NOSHOK 5-valve manifold by mounting a Steel or Stainless Steel bracket directly to the manifold body.

• Flange - Flange Mounting Kit, Steel (MK3-CS)
• Flange - Flange Mounting Kit, 304 Stainless Steel (MK3-SS2)
• NPT - NPT & NPT- Flange Mounting Kit, Steel (MK4-CS)
• NPT - NPT & NPT- Flange Mounting Kit, 304 Stainless Steel (MK4-SS2)

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

5-Valve Manifold Mounting Kit Dimensions

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

• Aflas (AF1)*                 
• Kalrez 3018 (KZ1)*                  
• Kalrez 4079 (KZ2)*                        
• Simriz 89D (KZ3)*     
• Kalrez 7075 (KZ4)*     
• Elast O Lion (EL1)*                 
• EPDM 80 (EM1)*
• EPDM 90 (EM2)*
• EPDM 70 (EM3)*
• NBR 70 (NB1)*
• EPDM 70 (EM1)**
• Kalrez 4079 (KZ2)**
• Elast O Lion (EL1)**
• Low Temperature FKM (VT1)*
• Low Temperature FKM (VT2)**

* For 1/8" NPT to 1/2" NPT only        
** For 3/4" NPT to 1-1/2" NPT only

The Static Adaptor is used to join threaded ports to a flange style connection. They are often used to join the NPT port of a static transmitter with a flange mounted connection on a Differential Pressure to Static Adaptor Plate. 

• Static Adaptor, 1/2” Female NPT, Steel (SAC-1)
• Static Adaptor, 1/2” Female NPT, Stainless Steel (SAS-1)
• Static Adaptor, 1/2” Male NPT, Steel (SAC-2)
• Static Adaptor, 1/2” Male NPT, Stainless Steel (SAS-2)

Specifications:

• Material: Zinc-Nickel plated Steel, 316 Stainless Steel
• Connections: 1/2" NPT Male-flange, 1/2" NPT Female-flange
• Other configurations available

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

WARNING: This product can expose you to chemicals including Lead, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov

The Vertical to Horizontal Adaptor Kit converts vertically mounted Stabilized Connectors to a horizontal position for mounting additional valves and instrumentation.

• Vertical to Horizontal Adaptor Kit, Steel (VHC)
• Vertical to Horizontal Adaptor Kit, Stainless Steel (VHS)

All 316SS products meet the requirements of NACE MR0175/ISO 15156-3.

---

WARNING: This product can expose you to chemicals including Nickel, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov